In Search of the Missing Fundamental: by Richard K. Jones
Random header image... Refresh for more!

The Duff Clearing Process

One of the most widely used methods for adjusting timpani heads is a process used by Cloyd Duff, who was timpanist of the Cleveland Orchestra from 1942 until 1981. It is a method he called clearing, and it involves a process of persuading the partials to more closely match those of a true harmonic series by careful adjustment of the tension rods.

Below is a brief synopsis of the key points in the Duff clearing process.

1. Objective: tune the membrane so that each lug is in-tune with the others allowing the drum to produce a clear sustained pitch.

2. Quiet space and patience are needed for extremely focused listening. Clear in increments of ten minutes and then take a break to rest the ear.

3. Place the drum on a platform so that your ear is level with the head.

4. Tune to a pitch in the middle range of the drum and use a hard stick when striking the head.

5. Place a mute in the center of the drum to damp high overtones. Mute other drums to avoid sympathetic vibrations.

6. If a drum has eight lugs* there will be two sets of tuning quadrants. Each quadrant-set will have two channels: primary and secondary.  Lugs directly inline with the beating spot are in the primary channel. Lugs perpendicular to the beating spot (orthogonal at 90º) are in the secondary channel. (see diagram below)

7. The primary channel will have more influence on the pitch at the time of the initial strike while the secondary channel will influence the pitch during the sustain/decay, especially if the drum is struck loudly.

8. If the sustained pitch rises after the initial strike, the primary channel is flat and needs to be raised.

9. If the sustained pitch flattens after the initial strike, the secondary channel needs to be raised.

10. With the drum set to the middle of its range,  strike the drum three times softly then listen, pause and then once loudly and listen.

11. The soft strokes will give you the pitch of the principal tone at the striking spot (primary channel), while the loud stroke will help determine whether a lug is sharp or flat in either the secondary channel or the other quadrant-set.

12. Ignore the overtones and focus on the principal tone only.**

13. Adjust lugs accordingly by making quarter turns only. This is so you can easily return the lug if it does not improve the sound. Use eighth turns as the clearing progresses.

14. Lugs work in pairs so remember to always check the opposing lug in both the primary and second channels.

15. Adjust only the channels within a quadrant-set as you move around the drum using the closs-lug tuning sequence. As you test the pitch with the loud and soft strokes at each rod, If the pitch goes slightly sharp or flat, it is most likely one of the tension rods in the primary or secondary channel. If the overall clarity of the pitch is muddy, the quadrant-sets are not matched.

16. When a soft stroke and a loud stroke any where around the circumference of the drum produces an even pitch and resonant tone at all dynamic levels, the head is clear.

* If a drum has five, six, or seven tuning lugs, the secondary channel(s) (and sometimes the opposing lug of the primary channel) will fall between two lugs. Adjusting these channels will have to be balanced between the two lugs adjacent to where the channel falls naturally. This type of head clearing is certainly more challenging, but can be achieved. Cloyd Duff’s 32″ Anheier Cable Drum (Seven Lug) is purported to be one of the best sounding drums ever made. See Clearing a Six Lug Timpano.

** One must be mindful to not confuse pitch with tone. No two points around the circumference of the drum will have exactly the same tone quality, but they can still have the same pitch. i.e., a bright quality can be mistaken as sounding sharp while a dull quality can be mistaken as being flat. Pitch and quality must be heard separately and with practice, the ability can be cultivated.

Fig. 1 (click to enlarge)

Figure 1 is the hypothetical mounting of a calf head for the drum to the direct right of the player. For this particular head, Area “A” on the neck proved to be the best playing spot. Backbone placement varies from player to player. Some place the backbone so it bisects the drum at lug points, others offset it a small amount. Some players prefer to mount a head so that the belly area is the primary striking spot. Others feel that the hip area usually has the best playing spots. No rules, just personal preferences; much depends on the integrity of the head itself, choice of primary playing spot(s), and the number of lugs a drum has (see below).  Most modern calf heads (Kalfo-VELLUM & PARCHMENT WORKS LTD, Maynooth Rd Co Kildare Naas Ireland +353 1628 82 70) are homogeneous enough to have multiple playing areas, so a strict adherence to past mounting practices is not always necessary. Players often rotate their heads once a favored playing spot becomes tired and worn.

PK-Anheier1

PK-Anheier

Cloyd Duff’s 32″ Anheier Cable Drum (Seven Lug)
belonging to Peter Kogan (retired) of the Minnesota Orchestra

How to clear a timpano with only six lugs.